大功率充電機啟動步驟（建議按此步驟操作）

1.按下電源開關“開”，充電指示燈在熄滅狀態，充電控制指示燈在“關”的狀態，此時可通過電壓調節和電流調節旋鈕預設充電電壓和充電電流。可通過面板時間繼電器預設充電時間，充電時間可從0—100小時任意設定。預設方法：按下“＞”按鈕，選擇時間位，按下“∧”按鈕，選擇所需時間值。選擇好后長按“RST”按鈕，即可設定充電時間。

2.預設好大功率充電機電壓和充電電流后，按下充電控制“開”按鈕，充電指示燈亮，大功率充電機開始充電。

注意事項：大功率充電機不充電有兩種情況：

1.反接充電后會產生嚴重后果。請謹慎操作。

2.電流調節電位器和電壓調節電位器在最小位置不充電。

三、大功率充電機充電過程介紹

大功率充電機開始充電時，充電機按照預設電流充電，電池電壓逐漸升高，當電池電壓達到設定電壓值時，充電電流自動減小，達到預設充電時間后充電機停止充電。

四、大功率充電機常見故障及維修

1. 電動汽車充電機不啟動，一般是由于空氣開關沒有和上、急停按鈕沒有復位或啟動按鈕壞造成的。

解決方法：檢查空氣開關和急停按鈕狀態，針對相應故障，更換相應器件。

2.電動汽車充電機工作過程中忽然停止工作，能自動恢復工作